• Brand: Van den broek biljarts
• Article code: vdb401714v
• Availability: In stock
• Delivery time: 1-5 workdays

Tip repair kit for replacing a cue tip yourself

Want to replace the tip of your billiard cue yourself? With this cue repair kit from Van den Broek Biljarts, you have all the tools you need to remove the old tip, flatten the ferrule, and glue on and finish a new tip.

The set is suitable for billiards enthusiasts who want to maintain their cue themselves. With the tip clamp, Razor, tip file, and Cue Cube, you work step by step towards a neatly finished tip.

Contents of the inspection repair kit

• Artemisia bitter orange glue. Store the glue in the refrigerator. Note: the bottle is approximately 1/6 full. This is the normal fill quantity.

• Wooden cue tip clip. To hold the cue tip in place while drying.

• Sanding block. For sanding flat and roughening the underside of the new cue tip.

• Yellow ferrule flattener. To make the top of the white cap clean and flat.

• Long cue tip file. For shaping and roughening the top of the cue tip.

• Cue Cube of your choice: Dime or Nickel. For applying the desired curvature.

• Razor cue tip cutter. To cut the side of the cue tip to size after gluing.

Choosing a Cue Cube: Dime or Nickel?

With the Cue Cube, you give the cue tip an even roundness. You can choose from two versions:

Dime: a stronger curvature. A choice for players who like to play with spin.

Nickel: a flatter curvature. A choice for players who prefer a less rounded tip.

The best choice depends on your playing style and personal preference. The curvature alone does not determine how much spin you apply.

Replace your cue tip yourself in 8 steps

1. Remove the old tip and flatten the ferrule

Carefully remove the old cue tip with a small knife. Make sure not to damage the white cap, also known as the ferrule.

Next, use the yellow ferrule flattener. Place the long section along the top end and rotate the tool slowly. Work until the gluing surface is clean and flat.

Never sand the ferrule freehand. This can cause the top to become convex or crooked. A flat ferrule is important for a good glue bond.

2. Prepare the new Seville orange

Place the sandpaper on a flat surface. Lightly sand the underside of the new cue tip. Ensure it is flat and remove the sanding dust before gluing.

3. Apply the Artemis glue

Apply a small drop of Artemis glue to the top of the ferrule. Place the tip and rotate it slightly so that the glue spreads over the contact surface. Then position the tip firmly in the center.

4. Place the wooden cue tip clamp

After gluing, secure the cue tip with the wooden cue tip clamp. Check that the cue tip remains straight. Allow the glue to dry completely according to the instructions on the packaging.

5. Cut the tip to size with the Razor

Once completely dry, touch up the protruding side of the tip with the Razor. Carefully place the Razor over the tip and work gently.

Pay attention to the combination of cue tip diameter and tip:

• For an 11 mm cue tip, use an 11.5 or 12 mm ferrule.

• For a 12 mm tip, use a 12.5 mm ferrule.

This excess is necessary to use the Razor properly. Check beforehand if the tool fits and do not force it over the top end.

6. Shape the top with the cue tip file

Use the long cue tip file to make the top slightly rounded and roughen it up. Work in small steps and check the shape regularly.

7. Finish the curve with the Cue Cube

Apply the final rounding with the selected Cue Cube. Use the Dime for a stronger curve or the Nickel for a flatter curve.

8. Check the cue tip and apply chalk

Remove the sanding dust. Check that the tip is firmly attached and neatly finished. Then apply billiard chalk. Your cue is ready for use again.

Buy cue repair kit at Van den Broek Biljarts

Do you want to maintain your billiard cue and replace the tip yourself? With this cue repair kit, you have the tools conveniently together. Choose the desired Cue Cube and give your tip the curvature that suits your game.

Are you unsure about the correct cue tip size or the use of the tool? Van den Broek Biljarts is happy to assist you with advice from our own workshop in Almere.